#11
|
|||
|
|||
Jason, from what I understand the M90 would be a bolt-in to your car (that is, if you could find one off a D24T from Europe, rare...)
We never got the M90 in anything in the US; our diesels were always available with manual but only with the M46. The M90 is a beast of a tranny, can hold massive amounts of power and is geared well, but was only ever sold elsewhere, in 940s and 960s. The M46 is stronger than the M47, though behind a diesel either one should be plenty strong enough. The later M47s are better but early M47s break easily. If you can find a late (Series II) M47, bolt up a D24T bellhousing and get the input shaft sleeve off a D24 or D24T M46 to make it fit the pilot bearing ID correctly, you would have a nice setup, and lighter than the M46 which has the overdrive unit hanging off the back. However, my understanding is that the second gen M47 was only offered in 240s, so you might have a speedo cable hole to plug up (700 series cars read speed off the diff while 200s use a cable off the trans tailshaft), and finding a correct driveshaft to fit the M47 into a 700 body would be tricky since they were very rare (only in non-turbo 8v gas 740s for a couple years in the late 80s-early 90s, and sold in very small numbers). Probably the easiest and safest bet is to just try to find a complete package with M46 and driveshaft from a D24T 700 car.
__________________
86 745 D24T/ZF 345k lifted 2.5" 83 764 D24T/M46 155k |
#12
|
||||
|
||||
I was meaning the later M47, I had heard the early ones were weak as you said. I would throw in a M47 or 46 whichever would come my way really. I am trying to get the M46 for sale on here but my better half is not interested in me spending any money on the car AT ALL. We have a wedding to pay for and so on... Either way, if a M47 would come around I dont think it would be too big a deal to just go to a drive shaft shop and have the front section made to match up to whats already there from the support bearing back. That sort of stuff isn't very expensive and probably easier than finding a 700 driveshaft that came with the M47 like you said. Hell there are almost no volvos around here at the local yards anyway, much less a V-8 M47 700 series! Ya right!
Jason
__________________
Back again with a '84 760 GLE D24T/ZF SOLD but not forgotten! 1984 760 Sedan, built D24Tic/ T-5 swapped My engine build: http://www.d24t.com/showthread.php?t...t=engine+build T-5 swap: http://d24t.com/showthread.php?399-W...to-quot-w-pics! |
#13
|
|||
|
|||
m90again
basicly its an 850 gear cluster converted to rear drive so its made to be short but its wide the laygear is beside the mainshaft rather than below it and worst of all the bell housing is not seperate from the main case ,so not the best idea I ever came up with then!
|
#14
|
|||
|
|||
Quote:
|
#15
|
|||
|
|||
tranny stuff
front drive volvos with sixes use GM auto box shame not rear drive also, or you could get shift kits and modded converters from hot rod/muscle car shops wonder if beemer guys do them for ZF? talking of hot rod shops ,could scan bellhousing and cut a plate then stuff T5 in there (dont tell the old lady)
|
#16
|
||||
|
||||
Yes a diesel M90 would be the way to go, but I doubt I'll ever see one here in the states... Oh well its a M46 or 47 for me.
Jason
__________________
Back again with a '84 760 GLE D24T/ZF SOLD but not forgotten! 1984 760 Sedan, built D24Tic/ T-5 swapped My engine build: http://www.d24t.com/showthread.php?t...t=engine+build T-5 swap: http://d24t.com/showthread.php?399-W...to-quot-w-pics! |
#17
|
|||
|
|||
Here in sweden there are a company that makes an adapter to a getrag six speed close ratio gearbox for the gasser cars but there is one problem you have to regear the final drive in the rear axle since the gear ratio of the gearbox is considerably lower than for the m46/47 / m90...
The m 90 is said to have problems with weak synchronization rings The m46 wich I have is fine but the electrical OD causes a some problems, I will se if an oil change will fix it later this week... The m47, well it is just weak and doesn´t have so high gear ratio in 5th as one would like. So out of the volvo gearboxes m90 would be the one to go for... I am sure there must be adapterplates for gearboxes in the us aswell.
__________________
If people where ment to be vegetarians, then why are cows made of meat?? |
#18
|
|||
|
|||
gas and deisel bellhousing
sorry i'm new to these cars, so i understand the gas and deisel bellhousings are different? i'm looking at a 84 760 d24t auto for pizza service and would enjoy myself alot more if it was manual. any help is appriciated. also how do these motors respond to wvo if done right?
|
#19
|
|||
|
|||
Yes bellhousings are totally different since the gasser is a volvo engine and the diesel is vw....
Pizza deliverycar with D24?? I would recomend some other car since these engines are built for long trips... I think you would kill it pretty quick.... vwo yes it works fine but the fuel pump needs to be resealed.... Best regards/ Tommy
__________________
If people where ment to be vegetarians, then why are cows made of meat?? |
#20
|
|||
|
|||
Any diesel would prob be OK for delivery driving, as long as you don't turn the engine on and off all the time. Lots of short trips are like one long trip as long as the engine stays warm and running the entire time.
rwd4evr where are you located?
__________________
86 745 D24T/ZF 345k lifted 2.5" 83 764 D24T/M46 155k |
|
|