D24T.com  

Go Back   D24T.com > Technical Discussion Area > Help! My car died!
Register FAQ Community Calendar Today's Posts Search

Reply
 
Thread Tools Display Modes
  #1  
Old 04-06-2014, 12:19 PM
CapnSass CapnSass is offline
Member
 
Join Date: Feb 2014
Location: The Rogue Valley
Vehicle: '84 245 d24
Posts: 30
Default IP Installation

Can someone remind me where the two ports on the topside of the injection pump connect to?? I have a picture but don't know how to upload.

Anyway, one faces towards the front of the car & the other back. Relatively between the throttle cable pulley & the injectors.

Thanks!!
Reply With Quote
  #2  
Old 04-06-2014, 12:40 PM
ngoma ngoma is offline
Supporting Member
 
Join Date: Nov 2009
Posts: 1,388
Default

Driveshaft side = fuel in.

High pressure out port side = fuel out.
__________________
1985 744 gle d24t
1985 745 gle d24t
Reply With Quote
  #3  
Old 04-06-2014, 12:46 PM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,655
Default

Make sure you get the banjo bolts in the right locations, too. The bolt for the outlet side has 'OUT' stamped large in the head and incorporates a screen and a very small orifice for fuel. If you get their locations reversed, it won't run too well!

Assume you have info and tools for setting injection timing?
Reply With Quote
  #4  
Old 04-06-2014, 01:22 PM
CapnSass CapnSass is offline
Member
 
Join Date: Feb 2014
Location: The Rogue Valley
Vehicle: '84 245 d24
Posts: 30
Default

Thanks!

So... The out port, where on the engine does it connect??
Reply With Quote
  #5  
Old 04-06-2014, 02:00 PM
CapnSass CapnSass is offline
Member
 
Join Date: Feb 2014
Location: The Rogue Valley
Vehicle: '84 245 d24
Posts: 30
Default

As far as the timing... We marked the spots from before. Since it was running great we planned to just line up the marks. ???
Reply With Quote
  #6  
Old 04-06-2014, 08:17 PM
745 TurboGreasel 745 TurboGreasel is offline
Senior Member
 
Join Date: Sep 2012
Location: Freedom CA
Vehicle: 85 745, 84Suburban 96Ram
Posts: 509
Default

The only way I've found to get it the same is to leave the belt engaged on both pulleys, and the cam pulley on, but close might be good enough. Even if you get it wrong, it will still run.most of the lines in pics here. http://www.competitiondiesel.com/for...d.php?t=120967
Reply With Quote
  #7  
Old 04-08-2014, 09:12 PM
v8volvo v8volvo is offline
Supporting Member
 
Join Date: Jun 2009
Location: Montana, USA
Vehicle: '86 745, '83 764
Posts: 1,655
Default

Quote:
Originally Posted by CapnSass View Post
As far as the timing... We marked the spots from before. Since it was running great we planned to just line up the marks. ???
As 745TG said, that will get you in the general ballpark, good chance close enough to start and run, but not optimal... If you want it to run as well as it can, proper timing with dial indicator is necessary. If you liked the way it worked before, putting it back together with everything visually in the same place won't guarantee it'll end up running the same. The marks are there for rough alignment and aren't a precise method for timing. Plus any difference in belt tension will affect timing too even if the marks are exactly where they were.

This would be like replacing the distributor on an old gasser motor and deciding that you could get away with a visual alignment of the dizzy and the block for timing. Sure you could easily enough get it to a spot where it would run okay, but to have it run the way it should, almost nobody would argue for trying to do the job without a timing light. In the same way, small changes in injection timing here can make noticeable differences in cold starting, power, smoke, mileage, engine life, EGT, etc...

The injection timing tools are some of the cheapest and easiest to find of everything that is needed for this motor, plenty of them cheap on ebay or available for loan for free from forum members here (see the Tool Rental thread), and not difficult to use. The benefits of getting timing right far outweigh the effort of getting and learning to use the timing equipment. If you like the car and want it to run its best, it is well worth it!
Reply With Quote
  #8  
Old 04-15-2014, 07:44 AM
CapnSass CapnSass is offline
Member
 
Join Date: Feb 2014
Location: The Rogue Valley
Vehicle: '84 245 d24
Posts: 30
Default

Quote:
Originally Posted by v8volvo View Post
As 745TG said, that will get you in the general ballpark, good chance close enough to start and run, but not optimal... If you want it to run as well as it can, proper timing with dial indicator is necessary. If you liked the way it worked before, putting it back together with everything visually in the same place won't guarantee it'll end up running the same. The marks are there for rough alignment and aren't a precise method for timing. Plus any difference in belt tension will affect timing too even if the marks are exactly where they were.

This would be like replacing the distributor on an old gasser motor and deciding that you could get away with a visual alignment of the dizzy and the block for timing. Sure you could easily enough get it to a spot where it would run okay, but to have it run the way it should, almost nobody would argue for trying to do the job without a timing light. In the same way, small changes in injection timing here can make noticeable differences in cold starting, power, smoke, mileage, engine life, EGT, etc...

The injection timing tools are some of the cheapest and easiest to find of everything that is needed for this motor, plenty of them cheap on ebay or available for loan for free from forum members here (see the Tool Rental thread), and not difficult to use. The benefits of getting timing right far outweigh the effort of getting and learning to use the timing equipment. If you like the car and want it to run its best, it is well worth it!
Thanks for this info! See my other posting for related response. Thanks so much.
Reply With Quote
Reply


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -8. The time now is 03:11 PM.


Powered by vBulletin® Version 3.8.10
Copyright ©2000 - 2024, vBulletin Solutions, Inc.